references
Comfort units
MAJOR LINE
TECHNICAL
Base DESCRIPTION
5 factory-fitted wired speeds (connected and available at the terminal) for customised adjustment. Sealed, tropicalised type, class F with protected shaft. Permanent capacitor. Roller bearings. Automatic overload protection as standard on winding. Elastic bushings. 230V single-phase 50/60 Hz power supply, reduced consumption. Single unit casing and side members in ABS PC V0 Front/rear panel in galvanised steel with mounting holes for easy fixing.
Asynchronous motor
Casing for CV/CH model
Bi-material casing in two colours: Flange, side member and supply air grille in RAL 7035 grey ABS PC Front pressed metal panel painted RAL 9010 white and front mounted return air grille (1D, 41D) in RAL 7035 grey Central access point for housing the built-in thermostats
Water coil
Electrical box
High performance coil concept Coil casing in galvanised panels. Copper tubes, continuous aluminium fins. Water coil tap on the left or right of the unit from the front of the supply air (to be specified when ordering). 2 or 4-tube main coil fitted with ½" or ¾" rotary couplings with air purge and drain screw. Additional coil for 4 tubes fitted with .½" rotary couplings with 40 mm centre-to-centre distance. Nominal pressure of 16 bar (at 20°C) Test pressure 24 bar. - 4-tube application: 90°C - 2-tube application: 90°C - 2-tube/2-wire application: 55°C (min. air flow: 200 m3/h)
Box incorporated on the side of the base opposite the hydraulics. Completely enclosed by an ABS/V0 cover. Electrical connection terminal on DIN rail in compliance with EN 50022, 7.5 mm deep. Wire clamps for customer connection.
Air filter
Flexible filter medium made of regenerative polyester fibre, on rigid frame. Efficiency class EN 779: G3. Fire rating: M1. Mounted on pivoting runners for easy maintenance
Packaging Control
Electric heater
Delivered in individual boxes on pallets protected by stretch wrap film.
Single tube 230V single phase 50/60 Hz electrical elements inserted into the aluminium housing. Two capillary tube temperature limiters with manual and automatic reset inserted in the aluminium housing.
Condensate drain pan
Pan in ABS V0 with M1 class reinforced EPS insulation (20 mm thick). Reinforced insulation for all climates, M1 class EPS panel (20 mm thick). ABS V0 auxiliary pan. 22 mm Ø external raised condensate outlet.
RTR-E electromechanical thermostat range. V30 electronic range. V300 electronic range. Networked electronic range (KNX): V3000. Networked electronic range (LON): V-LON2.
Factory-fitted options
Fan motor assembly
Impeller(s) in ABS V0 in split units for total accessibility of the different parts of the fan motor assembly. 160 mm HEE impeller(s), with CIAT exclusive airfoil blades in self-extinguishable ABS (V0). High energy efficiency motor enabling a reduction of up to 85% in electricity consumption. BLAC (Brushless Alternating Current) brushless technology offering more linear torque progression and a lower operating sound level than BLDC (Brushless Direct Current) technology. Sealed type, tropicalised with protected shaft. 3-speed gradual operation by 0-10V or on/off control signal, without expansion board. Internal normally closed series automatic thermal protection on the windings. "DFS" motor fault output using a photocoupler for potential alarm feedback via a Konnex protocol communication bus (via the V3000 controller). Mounted on silentbloc bushes. 230V±10%/1-Ph/50-60 Hz supply. Note: The minimum voltage to start up the motor is 2V. 362
Fan(s)
Condensate drain pump. Rectangular supply air sleeve for direct distribution in soffit. Supply and return air plenum for H and U assembly (contact us) for sizes 1 to 4. Electrical box on hydraulic side for NCH models only. Hydraulic coil with blades protected for use in harmful/ corrosive atmospheres (coastal locations, or areas close to chemical industries).
Accessories supplied separately
HEE motor
Note: refer to the technical manual and the instruction manual for more information.